This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
admin:poweroff [2023/01/30 13:24] peppe |
admin:poweroff [2023/09/08 13:45] peppe |
||
---|---|---|---|
Line 1: | Line 1: | ||
===== Διακοπή ρεύματος και επαναφορά ===== | ===== Διακοπή ρεύματος και επαναφορά ===== | ||
- | PRINT BEFORE USE! | + | PRINT BEFORE USE!\\ |
Material may not be available during shutdown process. | Material may not be available during shutdown process. | ||
- | Updated 30/01/2023\\ | + | Updated 30/08/2023\\ |
\\ | \\ | ||
* Altus KVM 10.1.2.10 | * Altus KVM 10.1.2.10 | ||
Line 13: | Line 13: | ||
Poweroff: | Poweroff: | ||
=== Επίπεδο 1 === | === Επίπεδο 1 === | ||
+ | |||
+ | == Unmount backup filesystem == | ||
+ | - uranus: umount /mnt | ||
+ | - gaia: umount /mnt | ||
+ | |||
+ | == EMC VNXe3100, 10.1.2.9 == | ||
+ | Poweroff procedure (+WAIT, UNPLUG!) | ||
+ | |||
+ | Shut down the system | ||
+ | | ||
+ | The shutdown process can take between 25 to 45 minutes to complete. | ||
+ | During this time, the connection to the system will be lost and | ||
+ | you will not have access to Unisphere or the online help. | ||
+ | | ||
+ | 1. From Unisphere, select Settings > Service System. | ||
+ | 2. Enter the Service password to access the Service System page. | ||
+ | 3. Under Service Actions, select Shut Down System. | ||
+ | 4. Click Execute service action to shut down the | ||
+ | | ||
+ | 5. In the Service Confirmation dialog box, click OK. | ||
+ | 6. Check the status of the shutdown process by looking at the | ||
+ | SP LED indicators: | ||
+ | | ||
+ | On VNXe3100 and VNXe3150 systems, the shutdown process is complete | ||
+ | when only the Storage Processor Power LEDs are blinking and all | ||
+ | other Storage Processor LEDs are off. | ||
+ | | ||
+ | 7. If you are relocating hardware, disconnect cables in the | ||
+ | | ||
+ | | ||
+ | Disconnect the power cables from disk-processor enclosure (DPE) | ||
+ | to power down the SPs. | ||
+ | Disconnect the power cable from the DAEs to power them down. | ||
+ | |||
+ | |||
== HP DL145G2 == | == HP DL145G2 == | ||
- Close control units poweroff | - Close control units poweroff | ||
- | - titan (old printserver), | + | - titan (old printserver, " |
- csforum, iLO 10.1.2.30\\ | - csforum, iLO 10.1.2.30\\ | ||
- aeolus, iLO 10.1.2.150\\ | - aeolus, iLO 10.1.2.150\\ | ||
Line 30: | Line 65: | ||
* Z-printer storage shutdown (Long button press -> shutdown procedure) | * Z-printer storage shutdown (Long button press -> shutdown procedure) | ||
| | ||
+ | == HP DL380G6 esxi5, 10.1.2.205, iLO 10.1.2.105 == | ||
+ | - alumni (alumni-vlan74)\\ | ||
+ | - dl380ws* | ||
+ | |||
== HP DL380G6 esxi2, 10.7.4.6, iLO 10.1.2.102 == | == HP DL380G6 esxi2, 10.7.4.6, iLO 10.1.2.102 == | ||
- | - titan-printserver (new printserver, | + | - titan-printserver (new printserver, |
- mysql-server (dbserver)\\ | - mysql-server (dbserver)\\ | ||
- calliope-www (cse www, calliope-vlan74)\\ | - calliope-www (cse www, calliope-vlan74)\\ | ||
Line 49: | Line 88: | ||
* gaia | * gaia | ||
- | == Dell R630 #1 (DOWN), 10.1.2.41, iLO 10.1.2.111 == | + | == Dell R630 #2 (DOWN), 10.1.2.41, iLO 10.1.2.111 == |
* uranus-nfs | * uranus-nfs | ||
=== Επίπεδο 3 === | === Επίπεδο 3 === | ||
- | |||
- | == EMC VNXe3100, 10.1.2.9 == | ||
- | Poweroff procedure (+WAIT, UNPLUG!) | ||
- | |||
- | Shut down the system | ||
- | | ||
- | The shutdown process can take between 25 to 45 minutes to complete. | ||
- | During this time, the connection to the system will be lost and | ||
- | you will not have access to Unisphere or the online help. | ||
- | | ||
- | 1. From Unisphere, select Settings > Service System. | ||
- | 2. Enter the Service password to access the Service System page. | ||
- | 3. Under Service Actions, select Shut Down System. | ||
- | 4. Click Execute service action to shut down the | ||
- | | ||
- | 5. In the Service Confirmation dialog box, click OK. | ||
- | 6. Check the status of the shutdown process by looking at the | ||
- | SP LED indicators: | ||
- | | ||
- | On VNXe3100 and VNXe3150 systems, the shutdown process is complete | ||
- | when only the Storage Processor Power LEDs are blinking and all | ||
- | other Storage Processor LEDs are off. | ||
- | | ||
- | 7. If you are relocating hardware, disconnect cables in the | ||
- | | ||
- | | ||
- | Disconnect the power cables from disk-processor enclosure (DPE) | ||
- | to power down the SPs. | ||
- | Disconnect the power cable from the DAEs to power them down. | ||
- | |||
== HP DL145G2 == | == HP DL145G2 == | ||
- | - scylla, iLO 10.1.2.45\\ | + | - scylla |
- rescue, iLO 10.1.2.49\\ | - rescue, iLO 10.1.2.49\\ | ||
Line 92: | Line 101: | ||
- gatepc74\\ | - gatepc74\\ | ||
- gatepc76\\ | - gatepc76\\ | ||
- | - clonezilla SE\\ | + | - clonezilla SE (drbl)\\ |
- charybdis\\ | - charybdis\\ | ||
Line 101: | Line 110: | ||
* Shutdown 10.1.2.40 | * Shutdown 10.1.2.40 | ||
* Shutdown 10.1.2.41 | * Shutdown 10.1.2.41 | ||
+ | * Shutdown 10.1.2.205 | ||
== Power cables == | == Power cables == | ||
Line 154: | Line 164: | ||
- csforum, iLO 10.1.2.30\\ | - csforum, iLO 10.1.2.30\\ | ||
- aeolus, iLO 10.1.2.150\\ | - aeolus, iLO 10.1.2.150\\ | ||
- | - glaucus\\ | + | - glaucus, iLO 10.1.2.29\\ |
- scylla, iLO 10.1.2.45\\ | - scylla, iLO 10.1.2.45\\ | ||
- rescue, iLO 10.1.2.49\\ | - rescue, iLO 10.1.2.49\\ | ||
Line 161: | Line 171: | ||
=== Επίπεδο 2 === | === Επίπεδο 2 === | ||
- | == Dell R630 #1 (DOWN), 10.1.2.41, iLO 10.1.2.111 == | + | == Dell R630 #2 (DOWN), 10.1.2.41, iLO 10.1.2.111 == |
* uranus-nfs | * uranus-nfs | ||
* check students FS | * check students FS | ||
* check grads FS | * check grads FS | ||
* check staff FS | * check staff FS | ||
- | * check quotas | + | * quotaoff -a |
+ | * quotacheck -a | ||
+ | * quotaon -a | ||
* mount /mnt | * mount /mnt | ||
Line 194: | Line 206: | ||
* mount / | * mount / | ||
- | == Εργαστήρια | + | == HP DL380G6 esxi5, 10.1.2.205, iLO 10.1.2.105 |
- | * Power up always on clients | + | |
+ | - dl380ws* | ||
| | ||
== 3D printers == | == 3D printers == | ||
Line 202: | Line 215: | ||
* Z-printer poweron | * Z-printer poweron | ||
* Z-printer storage poweron | * Z-printer storage poweron | ||
- | |||
- | == Rest == | ||
- | * glaucus (10.1.2.29) | ||
== Close control units == | == Close control units == |